For sales and support visit:
hubbellpowersystems.com/contact/
hubbellpowersystems.com/contact/
Corrosion-Resistant Anchors
See our Corrosion-Resistant Anchor Rods
Chance design offers many advantages
The Chance corrosion-resistant disc anchor is designed for low resistivity, alkaline and acidic soils with electrolyte combinations. The anchor eye is forged directly to the rod, so the eye is an integral part of the anchor. The anchor's flanged cap nut is cast iron. It's large and heavy for greater protection. The heat-shrink sleeve over the galvanized anchor rod helps prevent moisture from going down the rod. The insulating washer is fiberglass-reinforced thermoset material for better load-bearing properties compared to thermoform materials.
| Catalog No. | Description In. (mm) | Hole Size In. (mm) | Fits Protected Rod Size In. (mm) | Holding Capacity‡ - (lbs.(kN)) (No Safety Factors Included) vs Soil Class | ||||
|---|---|---|---|---|---|---|---|---|
| Class 3 500-600 in-lb | Class 4 400-500 in-lb | Class 5 300-400 in-lb | Class 6 200-300 in-lb | Class 7 100-200 in-lb | ||||
| C1022008 | 16 (406) Anchor .187 (4.7) Thick | 16 (406) | 3/4 (19.1) | 31000 (137.9)‡ | 26500 (117.9)‡ | 21000 (93.4) | 16500 (73.4) | 12000 (53.4) |
| C1022009 | 16 (406) Anchor .187 (4.7) Thick | 16 (406) | 1 (25.4) | 31000 (137.9)‡ | 26500 (117.9) | 21000 (93.4) | 16500 (73.4) | 12000 (53.4) |
| C1022011 | 20 (508) Anchor .187 (4.7) Thick | 20 (508) | 1 (25.4) | 40000 (177.9)‡ | 34000 (151.2) | 26000 (115.7) | 21500 (95.6) | 16000 (71.2) |
| C1022012 | 20 (508) Anchor .250 (6.3) Thick | 20 (508) | 1 (25.4) | 40000 (177.9)‡ | 34000 (151.2) | 26000 (115.7) | 21500 (95.6) | 16000 (71.2) |
| C1022054 | 24 (610) Anchor .187 (4.7) Thick | 24 (609) | 1 (25.4) | 50000 (222.4)‡ | 41000 (182.4)‡ | 33500 (149.0) | 26000 (115.7) | 20000 (89.0) |
| C1022050 | 24 (610) Anchor .250 (6.3) Thick | 24 (609) | 1 (25.4) | 50000 (222.4)‡ | 41000 (182.4)‡ | 33500 (149.0) | 26000 (115.7) | 20000 (89.0) |
Note: Capacity ratings apply to properly installed anchors only. Failure to install within 5° of alignment with the guy load will significantly lower strength.
Fiber-Reinforced Washer
| Catalog No. | Fits Rod Size | Approx. Wt./100 pcs. |
|---|---|---|
| C2100033 | 3/4" | 23 lb. |
| C2100034 | 1" | 19 lb. |
Cap Nut
| Catalog Number | Fits Rod Size | Approx. Wt./100 pcs. |
|---|---|---|
| C2050407 | 3/4 " | 242 lb. |
| C2050408 | 1 " | 242 lb. |
|
All contents Copyright© 2001 -
Hubbell Incorporated. All rights reserved. Because Hubbell has a policy of
continuous product improvement, we reserve the right to change design specifications
without notice.
Terms of Use | Contact Us | Site Map |